Man page - sg_rtpg(8)
Packages contains this manual
- scsi_start(8)
- sginfo(8)
- sg_scan(8)
- sg_luns(8)
- sg_bg_ctl(8)
- sg3_utils_json(8)
- sg_safte(8)
- sg_referrals(8)
- sg_sat_datetime(8)
- sg_vpd(8)
- sg_decode_sense(8)
- sg_rdac(8)
- sg_inq(8)
- sg_start(8)
- sg_timestamp(8)
- sg_z_act_query(8)
- sg_write_buffer(8)
- sg_sat_phy_event(8)
- sg_get_elem_status(8)
- sg_wr_mode(8)
- sg_rep_pip(8)
- scsi_mandat(8)
- sg_test_rwbuf(8)
- scsi_stop(8)
- sg_modes(8)
- sg_rmsn(8)
- sg_ses_microcode(8)
- sg_read_buffer(8)
- sgm_dd(8)
- scsi_readcap(8)
- sg_write_same(8)
- sg_rbuf(8)
- sg_rep_zones(8)
- sg_ident(8)
- sg_sat_set_features(8)
- sg_zone(8)
- sg_opcodes(8)
- sg_logs(8)
- sg_read_block_limits(8)
- sg_write_attr(8)
- sg_rep_density(8)
- sg_dd(8)
- sg_sanitize(8)
- sg_seek(8)
- sg3_utils(8)
- sg_compare_and_write(8)
- sg_requests(8)
- sg_reset(8)
- scsi_temperature(8)
- scsi_ready(8)
- sg_verify(8)
- sg_prevent(8)
- sg_sat_read_gplog(8)
- sg_persist(8)
- scsi_logging_level(8)
- sg_rtpg(8)
- sg_write_long(8)
- sg_senddiag(8)
- sg_format(8)
- sg_read_long(8)
- sgp_dd(8)
- sg_ses(8)
- sg_reassign(8)
- sg_map26(8)
- sg_get_lba_status(8)
- sg_get_config(8)
- sg_reset_wp(8)
- sg_unmap(8)
- sg_read(8)
- sg_write_verify(8)
- sg_rem_rest_elem(8)
- scsi_satl(8)
- rescan-scsi-bus.sh(8)
- sg_map(8)
- sg_emc_trespass(8)
- sg_write_x(8)
- sg_sat_identify(8)
- sg_sync(8)
- sg_copy_results(8)
- sg_stpg(8)
- sg_raw(8)
- sg_xcopy(8)
- sg_read_attr(8)
- sg_stream_ctl(8)
- sg_readcap(8)
- sg_turs(8)
apt-get install sg3-utils
Manual
SG_RTPG
NAMESYNOPSIS
DESCRIPTION
OPTIONS
NOTES
EXIT STATUS
AUTHORS
REPORTING BUGS
COPYRIGHT
SEE ALSO
NAME
sg_rtpg - send SCSI REPORT TARGET PORT GROUPS command
SYNOPSIS
sg_rtpg [ --decode ] [ --help ] [ --hex ] [ --raw ] [ --readonly ] [ --verbose ] [ --version ] DEVICE
DESCRIPTION
Send a SCSI REPORT TARGET PORT GROUPS command to DEVICE and outputs the response.
Target port group access is described in SPC-3 and SPC-4 found at www.t10.org . The most recent draft of SPC-4 is revision 37 in which target port groups are described in section 5.15 .
OPTIONS
Arguments to
long options are mandatory for short options as well.
-d
,
--decode
decodes the status code and asymmetric access state from each target port group descriptor returned. The default action is not to decode these values.
-e , --extended
use extended header format for parameter data. This sets the PARAMETER DATA FORMAT field in the cdb to 1.
-h , --help
output the usage message then exit.
-H , --hex
output response in hex (rather than partially or fully decode it).
-r , --raw
output response in binary to stdout.
-R , --readonly
open the DEVICE read-only (e.g. in Unix with the O_RDONLY flag). The default is to open it read-write.
-v , --verbose
increase the level of verbosity, (i.e. debug output).
-V , --version
print the version string and then exit.
NOTES
The Report Target Port Groups command should be supported whenever the TPGS bits in a standard INQUIRY response are greater than zero. [View with sg_inq utility.]
EXIT STATUS
The exit status of sg_rtpg is 0 when it is successful. Otherwise see the sg3_utils(8) man page.
AUTHORS
Written by Douglas Gilbert.
REPORTING BUGS
Report bugs to <dgilbert at interlog dot com>.
COPYRIGHT
Copyright ©
2004-2014 Christophe Varoqui and Douglas Gilbert
This software is distributed under a BSD-2-Clause license.
There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_inq(sg3_utils)