Man page - scsi_satl(8)
Packages contains this manual
- scsi_start(8)
- sginfo(8)
- sg_scan(8)
- sg_luns(8)
- sg_bg_ctl(8)
- sg3_utils_json(8)
- sg_safte(8)
- sg_referrals(8)
- sg_sat_datetime(8)
- sg_vpd(8)
- sg_decode_sense(8)
- sg_rdac(8)
- sg_inq(8)
- sg_start(8)
- sg_timestamp(8)
- sg_z_act_query(8)
- sg_write_buffer(8)
- sg_sat_phy_event(8)
- sg_get_elem_status(8)
- sg_wr_mode(8)
- sg_rep_pip(8)
- scsi_mandat(8)
- sg_test_rwbuf(8)
- scsi_stop(8)
- sg_modes(8)
- sg_rmsn(8)
- sg_ses_microcode(8)
- sg_read_buffer(8)
- sgm_dd(8)
- scsi_readcap(8)
- sg_write_same(8)
- sg_rbuf(8)
- sg_rep_zones(8)
- sg_ident(8)
- sg_sat_set_features(8)
- sg_zone(8)
- sg_opcodes(8)
- sg_logs(8)
- sg_read_block_limits(8)
- sg_write_attr(8)
- sg_rep_density(8)
- sg_dd(8)
- sg_sanitize(8)
- sg_seek(8)
- sg3_utils(8)
- sg_compare_and_write(8)
- sg_requests(8)
- sg_reset(8)
- scsi_temperature(8)
- scsi_ready(8)
- sg_verify(8)
- sg_prevent(8)
- sg_sat_read_gplog(8)
- sg_persist(8)
- scsi_logging_level(8)
- sg_rtpg(8)
- sg_write_long(8)
- sg_senddiag(8)
- sg_format(8)
- sg_read_long(8)
- sgp_dd(8)
- sg_ses(8)
- sg_reassign(8)
- sg_map26(8)
- sg_get_lba_status(8)
- sg_get_config(8)
- sg_reset_wp(8)
- sg_unmap(8)
- sg_read(8)
- sg_write_verify(8)
- sg_rem_rest_elem(8)
- scsi_satl(8)
- rescan-scsi-bus.sh(8)
- sg_map(8)
- sg_emc_trespass(8)
- sg_write_x(8)
- sg_sat_identify(8)
- sg_sync(8)
- sg_copy_results(8)
- sg_stpg(8)
- sg_raw(8)
- sg_xcopy(8)
- sg_read_attr(8)
- sg_stream_ctl(8)
- sg_readcap(8)
- sg_turs(8)
apt-get install sg3-utils
Manual
SCSI_SATL
NAMESYNOPSIS
DESCRIPTION
OPTIONS
EXIT STATUS
AUTHORS
COPYRIGHT
SEE ALSO
NAME
scsi_satl - check SCSI to ATA Translation (SAT) device support
SYNOPSIS
scsi_satl [ --help ] [ --log ] [ --quiet ] [ --verbose ] DEVICE
DESCRIPTION
This bash shell script calls several SCSI commands on the given DEVICE that is assumed to be an ATA device behind a SCSI to ATA Translation (SAT) layer (SATL). The results of each test and a pass/fail count are output.
OPTIONS
Arguments to
long options are mandatory for short options as well.
-h
,
--help
print out the usage message then exit.
-L , --log
the output to stderr (from each SCSI command executed) is appended to a file called ’scsi_satl.err’ in the current working directory.
-q , --quiet
the amount of output is reduced and typically only the pass/fail count is output.
-v , --verbose
increase level or verbosity.
EXIT STATUS
The exit status of this script is the number of "bad" errors found. So an exit status of 0 means all mandatory SCSI commands worked as expected.
AUTHORS
Written by D. Gilbert
COPYRIGHT
Copyright ©
2011-2013 Douglas Gilbert
This software is distributed under a BSD-2-Clause license.
There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_inq, sg_luns, sg_turs, sg_requests, sg_vpd, sg_senddiag, sg_modes, sg_sat_identify (sg3_utils)