Man page - scsi_stop(8)
Packages contas this manual
- sg_get_config(8)
- sg_safte(8)
- sg_write_verify(8)
- scsi_logging_level(8)
- sg_dd(8)
- sg_sat_datetime(8)
- scsi_temperature(8)
- sg_logs(8)
- sg_sat_phy_event(8)
- sg_rep_density(8)
- sg_ses(8)
- sginfo(8)
- sg_reset_wp(8)
- sg_turs(8)
- sg_write_long(8)
- sg_sat_read_gplog(8)
- sg_read_long(8)
- scsi_readcap(8)
- sg_rep_pip(8)
- sg_compare_and_write(8)
- sg_bg_ctl(8)
- sg_stream_ctl(8)
- sg_opcodes(8)
- sg_luns(8)
- sg_read(8)
- sg_get_elem_status(8)
- sg_sat_identify(8)
- sg3_utils(8)
- sg_sanitize(8)
- scsi_stop(8)
- sg_write_attr(8)
- sg_referrals(8)
- sg_rmsn(8)
- sg_readcap(8)
- sg_requests(8)
- sg_verify(8)
- sg_z_act_query(8)
- sgp_dd(8)
- sg_wr_mode(8)
- sg_unmap(8)
- sg_format(8)
- sgm_dd(8)
- sg_seek(8)
- sg_prevent(8)
- sg_ident(8)
- sg_rdac(8)
- sg_copy_results(8)
- sg_rem_rest_elem(8)
- sg_write_same(8)
- sg_sync(8)
- sg_read_buffer(8)
- sg_modes(8)
- sg_start(8)
- sg_decode_sense(8)
- sg_map26(8)
- sg_map(8)
- sg_test_rwbuf(8)
- sg_persist(8)
- sg_zone(8)
- sg_read_block_limits(8)
- scsi_ready(8)
- scsi_satl(8)
- sg_inq(8)
- sg_vpd(8)
- scsi_start(8)
- sg_write_buffer(8)
- sg_raw(8)
- sg_rtpg(8)
- sg_reset(8)
- rescan-scsi-bus.sh(8)
- sg_emc_trespass(8)
- sg_rbuf(8)
- sg_timestamp(8)
- sg3_utils_json(8)
- sg_rep_zones(8)
- sg_read_attr(8)
- sg_scan(8)
- sg_stpg(8)
- sg_write_x(8)
- sg_sat_set_features(8)
- scsi_mandat(8)
- sg_senddiag(8)
- sg_ses_microcode(8)
- sg_xcopy(8)
- sg_get_lba_status(8)
- sg_reassign(8)
apt-get install sg3-utils
Manual
| SCSI_STOP(8) | SG3_UTILS | SCSI_STOP(8) |
NAME
scsi_stop - stop (spin down) one or more SCSI disks
SYNOPSIS
scsi_stop [--help] [--verbose] [--wait] DEVICE [DEVICE]*
DESCRIPTION
This bash shell script calls the sg_start utility on each given DEVICE. The purpose is to spin down (stop) each given DEVICE.
OPTIONS
Arguments to long options are mandatory for short options as well.
- -h, --help
- print out the usage message then exit.
- -v, --verbose
- increase level or verbosity.
- -w, --wait
- wait for the spin down (stop) on each given DEVICE to complete. The default action is to do each stop in immediate mode.
NOTES
The sg_start utility calls the SCSI START STOP UNIT command and can either start (spin up) or stop (spin down) a SCSI disk depending on the given command line options.
EXIT STATUS
The exit status of this script is 0 when it is successful. Otherwise the exit status is that of the last sg_start utility called. See the sg3_utils(8) man page.
AUTHORS
Written by D. Gilbert
COPYRIGHT
Copyright © 2009-2013 Douglas Gilbert
This software is distributed under a BSD-2-Clause license. There is NO
warranty; not even for MERCHANTABILITY or FITNESS FOR A PARTICULAR
PURPOSE.
SEE ALSO
sg_start (sg3_utils)
| May 2013 | sg3_utils-1.36 |