Man page - scsi_temperature(8)
Packages contains this manual
- scsi_start(8)
- sginfo(8)
- sg_scan(8)
- sg_luns(8)
- sg_bg_ctl(8)
- sg3_utils_json(8)
- sg_safte(8)
- sg_referrals(8)
- sg_sat_datetime(8)
- sg_vpd(8)
- sg_decode_sense(8)
- sg_rdac(8)
- sg_inq(8)
- sg_start(8)
- sg_timestamp(8)
- sg_z_act_query(8)
- sg_write_buffer(8)
- sg_sat_phy_event(8)
- sg_get_elem_status(8)
- sg_wr_mode(8)
- sg_rep_pip(8)
- scsi_mandat(8)
- sg_test_rwbuf(8)
- scsi_stop(8)
- sg_modes(8)
- sg_rmsn(8)
- sg_ses_microcode(8)
- sg_read_buffer(8)
- sgm_dd(8)
- scsi_readcap(8)
- sg_write_same(8)
- sg_rbuf(8)
- sg_rep_zones(8)
- sg_ident(8)
- sg_sat_set_features(8)
- sg_zone(8)
- sg_opcodes(8)
- sg_logs(8)
- sg_read_block_limits(8)
- sg_write_attr(8)
- sg_rep_density(8)
- sg_dd(8)
- sg_sanitize(8)
- sg_seek(8)
- sg3_utils(8)
- sg_compare_and_write(8)
- sg_requests(8)
- sg_reset(8)
- scsi_temperature(8)
- scsi_ready(8)
- sg_verify(8)
- sg_prevent(8)
- sg_sat_read_gplog(8)
- sg_persist(8)
- scsi_logging_level(8)
- sg_rtpg(8)
- sg_write_long(8)
- sg_senddiag(8)
- sg_format(8)
- sg_read_long(8)
- sgp_dd(8)
- sg_ses(8)
- sg_reassign(8)
- sg_map26(8)
- sg_get_lba_status(8)
- sg_get_config(8)
- sg_reset_wp(8)
- sg_unmap(8)
- sg_read(8)
- sg_write_verify(8)
- sg_rem_rest_elem(8)
- scsi_satl(8)
- rescan-scsi-bus.sh(8)
- sg_map(8)
- sg_emc_trespass(8)
- sg_write_x(8)
- sg_sat_identify(8)
- sg_sync(8)
- sg_copy_results(8)
- sg_stpg(8)
- sg_raw(8)
- sg_xcopy(8)
- sg_read_attr(8)
- sg_stream_ctl(8)
- sg_readcap(8)
- sg_turs(8)
apt-get install sg3-utils
Manual
SCSI_TEMPERATURE
NAMESYNOPSIS
DESCRIPTION
OPTIONS
EXIT STATUS
AUTHORS
COPYRIGHT
SEE ALSO
NAME
scsi_temperature - fetch the temperature of a SCSI device
SYNOPSIS
scsi_temperature [ --help ] [ --verbose ] DEVICE [ DEVICE ]*
DESCRIPTION
This bash shell script calls the sg_logs utility on each given DEVICE in order to find the device’s temperature. The Temperature log page is checked first and if it is not available then the Informational Exceptions log page is checked.
OPTIONS
Arguments to
long options are mandatory for short options as well.
-h
,
--help
print out the usage message then exit.
-v , --verbose
increase level or verbosity.
EXIT STATUS
The exit status of this script is 0 when it is successful. Otherwise the exit status is that of the last sg_logs utility called. See the sg3_utils(8) man page.
AUTHORS
Written by D. Gilbert
COPYRIGHT
Copyright ©
2011-2013 Douglas Gilbert
This software is distributed under a BSD-2-Clause license.
There is NO warranty; not even for MERCHANTABILITY or
FITNESS FOR A PARTICULAR PURPOSE.
SEE ALSO
sg_logs (sg3_utils)