Man page - readsb(1)

Packages contains this manual

Manual

readsb

NAME
VERSION
DESCRIPTION
BUILD OPTIONS
USAGE
OPTIONS
NETWORK OPTIONS
RTLSDR OPTIONS
BLADERF OPTIONS
MODES BEAST OPTIONS
ADALM-Pluto OPTIONS
IFILE OPTIONS
HELP OPTIONS
DEBUG MODE FLAGS
CREDITS
BUGS
AUTHOR

NAME

readsb - Mode-S aircraft data processor for various receiver hardware.

VERSION

v3.8.1

DESCRIPTION

readsb Mode-S Receiver

BUILD OPTIONS

•

ENABLE_RTLSDR

•

ENABLE_BLADERF

USAGE

readsb [OPTION...]

OPTIONS

--dcfilter

Apply a 1Hz DC filter to input data (requires more CPU)

--enable-biastee

Enable bias tee on supporting interfaces (default: disabled)

--debug=<flags>

Debug mode (verbose), see flags below

--device-type=<type>

Select SDR type

--fix

Enable CRC single-bit error correction (default)

--forward-mlat

Allow forwarding of received mlat results to output ports

--freq=<hz>

Set frequency (default: 1090 MHz)

--gain=<db>

Set gain (default: max gain. Use -10 for auto-gain)

--gnss

Show altitudes as GNSS when available

--interactive

Interactive mode refreshing data on screen. Implies --throttle

--interactive-ttl=<sec>

Remove from list if idle for <sec> (default: 60)

--json-location-accuracy=<n>

Accuracy of receiver location in json metadata:

0

no location

1

approximate

2

exact

--lat=<lat>

Reference/receiver surface latitude

--lon=<lon>

Reference/receiver surface longitude

--max-range=<dist>

Absolute maximum range for position decoding (in nm, default: 300)

--metric

Use metric units

--mlat

Display raw messages in Beast ASCII mode

--modeac

Enable decoding of SSR Modes 3/A & 3/C

--no-crc-check

Disable messages with invalid CRC (discouraged)

--no-fix

Disable CRC single-bit error correction

--no-interactive

Disable interactive mode, print to stdout

--no-modeac-auto

Don’t enable Mode A/C if requested by a Beast connection

--onlyaddr

Show only ICAO addresses

--quiet

Disable output. Use for daemon applications

--raw

Show only messages hex values

--show-only=<addr>

Show only messages by given ICAO on stdout

--snip=<level>

Strip IQ file removing samples < level

--stats

With --ifile print stats at exit. No other output

--stats-every=<sec>

Show and reset stats every <sec> seconds

--stats-range

Collect/show range histogram

--write-json=<dir>

Periodically write json output to <dir> (for external webserver)

--write-json-every=<t>

Write json output every t seconds (default 1)

NETWORK OPTIONS

--net

Enable networking

--net-bi-port=<ports>

TCP Beast input listen ports (default: 30004,30104)

--net-vrs-port=<ports>

TCP VRS json output listen ports (default: 0)

--net-beast-reduce-out-port=<ports>

TCP BeastReduce output listen ports (default: 0)

--net-beast-reduce-interval=<seconds>

BeastReduce position update interval, longer means less data (default: 0.125, valid range: 0.000 - 14.999)

--net-bind-address=<ip>

IP address to bind to (default: Any; Use 127.0.0.1 for private)

--net-bo-port=<ports>

TCP Beast output listen ports (default: 30005)

--net-buffer=<n>

TCP buffer size 64Kb * (2ˆn) (default: n=0, 64Kb)

--net-heartbeat=<rate>

TCP heartbeat rate in seconds (default: 60 sec, 0 to disable)

--net-only

Enable just networking, no RTL device or file used

--net-connector=<ip,port,protocol>

Establish connection, can be specified multiple times (example: 127.0.0.1,23004,beast_out) Protocols: beast_out, beast_in, raw_out, raw_in, sbs_out, vrs_out.

--net-connector-delay=<seconds>

Outbound re-connection delay (default: 30)

--net-ri-port=<ports>

TCP raw input listen ports (default: 30001)

--net-ro-interval=<rate>

TCP output memory flush rate in seconds (default: 0)

--net-ro-port=<ports>

TCP raw output listen ports (default: 30002)

--net-ro-size=<size>

TCP output minimum size (default: 0)

--net-sbs-port=<ports>

TCP BaseStation output listen ports (default: 30003)

--net-verbatim

Forward messages unchanged

RTLSDR OPTIONS

use with --device-type rtlsdr
--device=<index|serial>

Select device by index or serial number

--enable-agc

Enable digital AGC (not tuner AGC!)

--ppm=<correction>

Set oscillator frequency correction in PPM

BLADERF OPTIONS

use with --device-type bladerf
--bladerf-bandwidth=<hz>

Set LPF bandwidth (’bypass’ to bypass the LPF)

--bladerf-decimation=<N>

Assume FPGA decimates by a factor of N

--bladerf-fpga=<path>

Use alternative FPGA bitstream (’’ to disable FPGA load)

--device=<ident>

Select device by bladeRF ’device identifier’

MODES BEAST OPTIONS

use with --device-type modesbeast

Beast binary protocol and hardware handshake are always enabled.
--beast-crc-off

Turn OFF CRC checking

--beast-df045-on

Turn ON DF0/4/5 filter

--beast-df1117-on

Turn ON DF11/17-only filter

--beast-fec-off

Turn OFF forward error correction

--beast-mlat-off

Turn OFF MLAT time stamps

--beast-modeac

Turn ON mode A/C

--beast-serial=<path>

Path to Beast serial device (default /dev/ttyUSB0)

ADALM-Pluto OPTIONS

use with --device-type plutosdr

Default device expected at hostname ’pluto.local’.
--pluto-uri=<USB URI>

Create USB context from URI (eg. usb:1.2.5)

--pluto-network=<hostname or IP>

Create network context from hostname or IP (default pluto.local)

IFILE OPTIONS

use with --ifile
--ifile=<path>

Read samples from given file (’-’ for stdin)

--iformat=<type>

Set sample format (UC8, SC16, SC16Q11)

--throttle

Process samples at the original capture speed

HELP OPTIONS

-?, --help

Give this help list

--usage

Give a short usage message

-V, --version

Print program version

DEBUG MODE FLAGS

d

Log frames decoded with errors

D

Log frames decoded with zero errors

c

Log frames with bad CRC

C

Log frames with good CRC

p

Log frames with bad preamble

n

Log network debugging info

j

Log frames to frames.js, loadable by debug.html

CREDITS

Matthias Wirth aka wiedehopf Taner Halicioglu aka tanerH

BUGS

Report bugs to Michael Wolf <michael@mictronics.de>.

AUTHOR

Michael Wolf